A red plate for a red line, a green plate for a green one

The best laser target plates for 2026

A target plate is a tinted card that makes a laser line jump out where the wall itself does not show it — dark brick, glass, anything wet. The tint is matched to the diode: a red plate does very little for a green line and the reverse is equally true, which is the one specification people get wrong. Magnetic backing and a printed scale turn the plate into a marking aid. We compare tint color, magnetic backing, printed scales and crosshairs, reflective coatings, and size.

By Jean-Benoit Buisson

What we recommend

1. 

   MOETER Red laser target plate, 1.3× film, floor stand

   The only plate here with a numbered brightness gain — on a red plate whose own listing says it suits green lasers as well.

   Functions

   A special reflective target film stated to increase the brightness of RED laser lines or points by 1.3 times in long-distance or bright sunlight conditions. One point three is the ONLY numbered gain on this shelf — the other plates say reflective backing, or high-contrast, and leave you to judge

   Scale

   Center-zero scales in BOTH inches and centimeters, stated easy to read. Center zero is the detail that matters: a target plate is used to transfer a line, and a scale reading outward from the middle gives the offset directly in either direction without arithmetic

   Reference and mounting

   Three fixings, stated: strong magnets for metal studs, a hole for hook mounting, and a fold-out back stand to stand it upright on a floor. Three routes is the most on this shelf, and the floor stand is what makes a plate usable where there is no steel and nothing to hang it on

   Also stated

   The fourth bullet reads: "compatible with both red and green beam laser levels". This shelf's introduction says a red plate does very little for a green line and calls that the one specification people get wrong, and the buying tip warns that listings frequently show both plates lit by the same beam. This is a RED plate, sold beside the maker's own GREEN plate at the same price — the two exist precisely because the tints are not interchangeable

   Material

   Lightweight and rugged, stated, compact enough for a toolkit. No dimensions and no weight appear, where one plate on this shelf publishes 10 × 7 cm (3.9 × 2.8 in) and 30 g (1.1 oz)

   Supplied

   The plate. The parcel weighs 27 g (1 oz), which is consistent with a single card rather than a pair — two plates on this shelf ship in multiples

   Amazon reference

   B0DCFL4DXX

   EAN

   0711271802087

   • A numbered gain: 1.3× on a red line
   • Center-zero scales, so the offset reads directly
   • Its fourth bullet claims green compatibility on a red plate

   Best for: A red laser on dark brick, wet concrete or glass, where the line disappears into the wall

   ≈ $9

   Check price on Amazon
2. 

   VGECEE Magnetic laser target plates, pair

   Two magnetic target plates in high-strength ABS, scaled in both inches and centimeters, at the price most makers charge for one.

   Amazon reference

   B0F2HX7D3N (identical on 5 markets)

   EAN

   0692878773638

   Supplied

   Two plates

   Material

   ABS

   Stated dimension or range

   inch and centimeter scales

   Reference and mounting

   two magnets in the base

   • Two plates in the pack — a laser line usually needs a target at each end of the run
   • Two magnets in the base, so it holds on steel studs and nails without a hand
   • The tint color is not stated in the listing — target plates are matched to a diode color

   Best for: Marking both ends of a laser line without holding anything.

   Search Amazon for this model
3. 

   Huepar Green laser target plate

   A green target plate with a reflective film rather than just a tint, a marked central zero point, and three ways of mounting it — magnets, a hanging hole and a back stand.

   Amazon reference

   B075XCC1GJ (identical on 5 markets)

   EAN

   0790996362816

   Optical

   Green tint · reflective target film

   Also stated

   central zero

   Reference and mounting

   magnets, hook hole and stand

   • States its color — green — which is the specification that decides whether it works with your laser
   • A special reflective target film, stated to increase visibility beyond a plain tint
   • Green only — useless with a red laser

   Best for: Green line lasers, where the reflective film and the central zero earn their premium.

   Search Amazon for this model
4. 

   MOETER Green laser target plate, 1.3× film, floor stand

   The green half of the only matched pair on this shelf — and the half that does not overclaim.

   Functions

   A special reflective target film stated to boost the visibility of GREEN laser lines or points by 1.3 times, for long-distance work or bright sunlight. The same numbered gain as the maker's red plate, and the only numbered gain on this shelf

   Also stated

   Universal compatibility with GREEN BEAM laser levels, rotary lasers, cross-line lasers and laser measures — green, and only green. That is the correct claim, and it is worth noting because the maker's own RED plate claims compatibility with both colors. This shelf's introduction says a plate does very little for the other diode; this listing agrees with the shelf and its twin does not

   Scale

   Dual measurement scales with Center ZERO in inches and centimeters, stated for framing, tiling and HVAC installation. Center zero gives the offset from the line directly, upward or downward, with no arithmetic

   Reference and mounting

   Three fixings: strong magnets for metal surfaces, a hanging hole, or a fold-out floor stand. The stand is what makes the plate work in an empty room with no steel and nothing to hang on

   Material

   Lightweight yet rugged, stated to withstand tough environments, compact for a toolkit. No dimensions and no weight appear

   Supplied

   The plate. No count is published, and no parcel weight was recorded for this line

   Amazon reference

   B0DCFBSL23

   EAN

   0711271802070

   • A numbered gain: 1.3× on a green line
   • It claims green only, which is the honest claim
   • No dimensions and no weight published

   Best for: A green laser outdoors or on dark brick, where the line vanishes within a few meters

   ≈ $9

   Check price on Amazon
5. 

   Bosch Professional Laser target plate with stand

   A target plate aimed at laser distance meters rather than line lasers — a different job, and one that most target plates are not sold for.

   Amazon reference

   B00D5AILSK (identical on 6 markets)

   EAN

   3165140617505

   Also stated

   For laser distance meters

   Optical

   improved beam visibility

   Supplied

   with stand

   • Stated for laser distance meters, which is a use most target plates do not mention
   • A stand and a handy size, stated as making it usable anywhere
   • The tint color is not stated

   Best for: Long measurements with a distance meter, where the dot has to land on something you can see.

   Check price on Amazon
6. 

   SMTOER Target plates, 2 green and 2 red, 10 × 7 cm (3.9 × 2.8 in)

   The only box on this shelf that answers the tint question by containing both answers — and the only plate that tells you how big it is.

   Supplied

   Two RED and two GREEN plates in one package, stated. It is the only set on this shelf that covers both diode colors — this shelf's introduction says the tint must match the diode and calls it the one specification people get wrong, and this box removes the decision. It also gives two plates per color, which is what transferring a line across a room actually takes

   Stated dimension or range

   10 × 7 cm (4 × 2.8 in), 30 g each, with a slim profile for a pocket or toolkit. It is the ONLY published size on this shelf — this shelf's introduction lists size as one of five comparisons and at least six of the ten plates here leave it to the photograph

   Scale

   Front-facing BULLSEYE patterns with dual-unit scales in inches and centimeters, stated to enable accurate measurements. A bullseye rather than a cross: concentric rings give a center that can be judged from any angle, where a cross has to be read square on

   Functions

   A reflective backing stated to enhance laser spot recognition in direct sunlight or low light. No brightness gain figure is published, where one maker on this shelf states 1.3×

   Material

   Durable ABS plastic, stated, with a magnetic base for metal surfaces. ABS is named, which four plates on this shelf do not do — a rigid plate stays flat where a card curls

   Reference and mounting

   A magnetic base for attachment to metal surfaces, and the title states a stand. No hook hole is published, and two plates on this shelf publish three fixing routes

   Amazon reference

   B0FNMYRHF9

   EAN

   0712110938646

   • Two red and two green: both diodes covered in one box
   • The only published size and weight on this shelf
   • No brightness gain figure

   Best for: A van with a red laser and a green one, or two plates at each end of a line

   ≈ $32

   Check price on Amazon
7. 

   Johnson Green laser target, X pattern, rare-earth magnets

   The only plate here that says what its magnets are made of, and the only one that gives you two places to put them.

   Reference and mounting

   DUAL-POSITION rare-earth magnets, stated. Two things here that nothing else on this shelf publishes: the magnet MATERIAL — rare earth, meaning neodymium, which holds several times harder than the ferrite magnet in a cheap plate — and TWO positions, so the plate can be hung in either orientation on the same steel without rotating the scale

   Scale

   Dual inch and centimeter measuring scales, stated. Johnson does not say whether zero is at the center or an edge, which four plates on this shelf do state

   Functions

   A high-contrast X design stated to allow fast, efficient positioning, for use with GREEN lasers. An X is read by laying the line along one arm, which is quick when you are square to the plate; a bullseye on another plate here reads the same from any angle. No brightness gain figure is published

   Body and fittings

   A geometric design stated to provide maximum stability. On a plate that hangs from magnets, stability means it does not rotate or slide under its own weight — which is exactly what two magnet positions and a shaped body address together

   Also stated

   For use with GREEN lasers, stated plainly and without hedging. Johnson Level & Tool is a US level manufacturer rather than a trading brand, which is the reason the magnet specification is there at all

   Supplied

   The target. No dimensions, no weight and no count appear, and no floor stand or hook hole is published — the magnets are the only fixing

   Amazon reference

   B0D21HFNCC

   EAN

   0049448067657

   • Rare-earth magnets, the only magnet type named here
   • Two magnet positions, so either orientation works
   • Magnets only: no hook hole and no floor stand

   Best for: Steel-framed interiors, where the plate goes on a stud and must not slide

   ≈ $11

   Check price on Amazon
8. 

   YOTOM Red laser targets, pair, magnetic

   Two plates for nine dollars — and a pair is what a level transfer needs, which single plates on this shelf cost more than.

   Supplied

   TWO plates, stated. A pair is what a level transfer actually takes — a plate at the datum and a plate at the far wall, so the line can be checked without moving anything — and at nine dollars for two this is the cheapest magnetic pair on this shelf, where single plates run eight to twenty-nine dollars

   Functions

   Stated to help locate the beam for accurate measurement away from the laser unit, and suitable for laser levels, rotary lasers, cross-line lasers, laser measures and all RED beam laser levels. Red, stated in the title and again in the last bullet — no claim to green, which this shelf's introduction says is the distinction people get wrong

   Reference and mounting

   Magnets for convenient attachment to metal studs, stated. Magnets are the only fixing: no hook hole and no floor stand, so no steel means no plate. Nothing is published about the magnet type

   Scale

   Increments in INCH and CM, stated easy to read. Whether zero sits at the center or an edge is not stated, which four plates on this shelf do publish

   Stated dimension or range

   Not published as a figure — stated only as small and handy enough to fit inside a laser kit, which is the right design brief and not a measurement. One plate on this shelf publishes 10 × 7 cm (3.9 × 2.8 in)

   Also stated

   No brightness gain figure and no reflective film is claimed. Two plates on this shelf state 1.3×, and this one describes no coating at all — so what it offers is the tint and the scale rather than a measured gain

   Amazon reference

   B08MKGBRV5

   EAN

   0738631118176

   • Two plates, which is what a transfer needs
   • Nine dollars for the pair, the cheapest magnetic pair here
   • No brightness gain figure and no reflective film claimed

   Best for: Setting a datum at one wall and checking it at the other, with a red laser

   ≈ $9

   Check price on Amazon
9. 

   HOZO Target cards, 4 pcs, adhesive, washable

   The only target here that works on glass and concrete — because it is glue, not a magnet — and the only one with a published reuse count.

   Reference and mounting

   ADHESIVE, not magnetic: stated to attach to any surface including walls, CONCRETE, wood and GLASS. It is the only non-magnetic plate on this shelf and that is its reason to exist — a magnet needs steel, and a glazed shopfront, a poured slab or a plastered room offers none. This shelf's introduction lists magnetic backing as one of five comparisons; this plate answers the question the other way

   Also stated

   Washable and reusable, stated to retain their stickiness up to 100 TIMES. It is the only reuse count published on this shelf, and on an adhesive product it is the figure that decides whether this is a consumable or a tool — a hundred uses at under five dollars a card is a long time

   Supplied

   Four cards, stated, at nineteen dollars — about four dollars seventy-five each, the lowest price per plate on this shelf. The same maker's single magnetic plate on this shelf costs twenty-nine dollars

   Functions

   Stated suitable for alignment, laser levels, rotating lasers, cross lasers and laser measurement, and for the maker's own M-Cube laser distance meter. NO TINT Color is stated — neither red nor green — on a shelf whose tag reads: a red plate for a red line, a green plate for a green one

   Scale

   NONE. No increments, no center zero and no crosshair is published. This shelf's introduction says a printed scale is what turns a plate into a marking aid; at least five of the ten plates here carry one and this is not among them

   Stated dimension or range

   Not published. No size and no thickness appears, and the parcel weighs 20 g (0.7 oz) for four cards — which describes a card rather than a board

   Amazon reference

   B0CCRGQ23L

   EAN

   0860006740894

   • It sticks to glass and concrete, where magnets fail
   • Four cards for nineteen dollars, under five each
   • No tint color stated at all

   Best for: Glass, concrete and plastered walls, where there is no steel for a magnet anywhere

   ≈ $19

   Check price on Amazon
10. 

    HOZO Magnetic washable target plate for M-Cube 02

    Magnetic and washable in one plate, which nothing else here manages — at six times the price per plate of the same maker's cards.

    Reference and mounting

    Strong built-in magnets for secure attachment to metal surfaces, stated. Combined with the washable material below, this is the only plate on this shelf that is BOTH magnetic and washable — the adhesive cards from the same maker are washable and not magnetic, and the five magnetic plates here say nothing about being washed

    Material

    Durable, water-resistant material, stated — rinse and reuse for long-term performance. On a plate that gets set on a dusty slab and then on a window, a face that can be rinsed rather than wiped is the difference between a clean target and a grey one

    Functions

    Stated to improve laser DOT detection in bright or long-range conditions, and designed specifically to work with the HOZO M-Cube 02 laser distance meter. Note the word dot: this is aimed at a point laser, a distance meter, rather than at a line — which is a different job from most of this shelf

    Also stated

    NO TINT Color, on a shelf whose tag reads "a red plate for a red line, a green plate for a green one". Neither HOZO listing here publishes one, and this shelf's introduction calls the tint the one specification people get wrong

    Scale

    NONE published. No increments, no center zero and no crosshair — so the plate makes a dot visible and does not help you measure from it. At least five of the ten plates on this shelf carry a scale

    Stated dimension or range

    Not published. The parcel weighs 68 g (2.4 oz), which is more than twice the 30 g (1.1 oz) of the plate on this shelf that does publish its size

    Amazon reference

    B0DY7CCWMZ

    EAN

    0850059742235

    • Magnetic and washable, which nothing else here is both of
    • A water-resistant face that rinses rather than wipes
    • Twenty-nine dollars, the most expensive plate on this shelf

    Best for: A HOZO M-Cube 02 owner who wants one plate that goes on steel and wipes clean

    ≈ $29

    Check price on Amazon